50 lines
2.0 KiB
Plaintext
50 lines
2.0 KiB
Plaintext
Load "TEST_C8T6\\TEST_C8T6.axf"
|
|
Set JLink Project File to "d:\synchronous\School\STM32\CubeMX\F103C8T6\TEST_C8T6\MDK-ARM\JLinkSettings.ini"* JLink Info: Device "STM32F103C8" selected.
|
|
|
|
JLink info:
|
|
------------
|
|
DLL: V7.00a, compiled Apr 16 2021 15:32:47
|
|
Firmware: J-Link ARM-OB STM32 compiled Aug 22 2012 19:52:04
|
|
Hardware: V7.00
|
|
S/N : 20090930
|
|
Feature(s) : RDI,FlashDL,FlashBP,JFlash,GDBFull
|
|
|
|
* JLink Info: InitTarget() start
|
|
* JLink Info: InitTarget() end
|
|
* JLink Info: Found SW-DP with ID 0x1BA01477
|
|
* JLink Info: DPv0 detected
|
|
* JLink Info: Scanning AP map to find all available APs
|
|
* JLink Info: AP[1]: Stopped AP scan as end of AP map has been reached
|
|
* JLink Info: AP[0]: AHB-AP (IDR: 0x14770011)
|
|
* JLink Info: Iterating through AP map to find AHB-AP to use
|
|
* JLink Info: AP[0]: Core found
|
|
* JLink Info: AP[0]: AHB-AP ROM base: 0xE00FF000
|
|
* JLink Info: CPUID register: 0x411FC231. Implementer code: 0x41 (ARM)
|
|
* JLink Info: Found Cortex-M3 r1p1, Little endian.
|
|
* JLink Info: FPUnit: 6 code (BP) slots and 2 literal slots
|
|
* JLink Info: CoreSight components:
|
|
* JLink Info: ROMTbl[0] @ E00FF000
|
|
* JLink Info: ROMTbl[0][0]: E000E000, CID: B105E00D, PID: 001BB000 SCS
|
|
* JLink Info: ROMTbl[0][1]: E0001000, CID: B105E00D, PID: 001BB002 DWT
|
|
* JLink Info: ROMTbl[0][2]: E0002000, CID: B105E00D, PID: 000BB003 FPB
|
|
* JLink Info: ROMTbl[0][3]: E0000000, CID: B105E00D, PID: 001BB001 ITM
|
|
* JLink Info: ROMTbl[0][4]: E0040000, CID: B105900D, PID: 001BB923 TPIU-Lite
|
|
ROMTableAddr = 0xE00FF000
|
|
* JLink Info: Reset: Halt core after reset via DEMCR.VC_CORERESET.
|
|
* JLink Info: Reset: Reset device via AIRCR.SYSRESETREQ.
|
|
|
|
Target info:
|
|
------------
|
|
Device: STM32F103C8
|
|
VTarget = 3.300V
|
|
State of Pins: TCK: 0, TDI: 0, TDO: 1, TMS: 0, TRES: 1, TRST: 0
|
|
Hardware-Breakpoints: 6
|
|
Software-Breakpoints: 8192
|
|
Watchpoints: 4
|
|
JTAG speed: 4000 kHz
|
|
|
|
Erase Done.Programming Done.Verify OK.* JLink Info: Reset: Halt core after reset via DEMCR.VC_CORERESET.
|
|
* JLink Info: Reset: Reset device via AIRCR.SYSRESETREQ.
|
|
Application running ...
|
|
Flash Load finished at 22:21:13
|